1.     概述

General

此型號DYT36V30A 340×230×130mm的鋁質外殼充電器能在輸出36Vdc/30A的情況下工作，具有反接保護功能。

Battery Charger DYT36V30A 340×230×130mm can work normally under 36Vdc/30A and with reverse polarity protection.

2.     主要參數

Main product specification

3.     環境條件

Environmental condition

4.     技術特征

Electrical characteristics

4.1 輸入特征：

   Input characteristic

4.2 輸出特征和充電模式：

   Output characteristic or charge stages

4.3 保護特征：

    Protection characteristics

4.4 充電指示

   Charging indicator

5.     安全性&電池兼容性

Safety & EMC

備注：辨識A：在技術要求范圍內，充電器功能正常；

Remark: Discrimination A- Function OK under technical requirement range;       

辨識R：只有由外部干擾信號引起的保護裝置（保險絲）損壞，整個設備在更換保護裝置和重設運行參數后才能正常工作，因機械性損壞和設備故障的設備卻不能。

Discrimination R- Physical damage or failure of equipment are not allowed, but damage of protection device (fuse) caused by interference signal of outside is allowed, and the whole equipment can work normally after replacement of protection device and reset of running parameter

6.     環境測試要求

Environmental testing requirements

7.     機械特征

Mechanical characteristic:

外殼材質：鋁

Shell material: Aluminum

外殼尺寸: 長*寬*高=340×230×130毫米

Outline dimension: L*W*H=450×350×238mm

輸入接口: 通過IEC 標準

Input socket: meets IEC standard

電源線: 1.5米長

AC wires: value="1.5" tcsc="0" unitname="m" w:st="on">1.5m length

輸出線: 1.5米長

DC wire: value="1.5" tcsc="0" unitname="m" w:st="on">1.5m length

凈重: 7.5千克

Net Weight: value="7.5" tcsc="0" unitname="kg" w:st="on">7.5Kg

8. 包裝，運輸方式和存儲方式  Package, transportation & storage

8.1 包裝  Package:

   包裝盒內有產品名稱，型號，生產廠家名稱，安全標準，序號，使用說明書以及裝箱單。

   There is product name, model, name of manufacturer, safety approval, serial number, User Manual and packing

list in the package box.

8.2運輸方式  Transportation：

:

   適用于貨車裝運，產品需放在陰處，裝卸時請小心。

   Suit for transportation by truck, the products should be shielded by tent from sunshine, and loaded and unloaded carefully.

8.3存儲方式 Storage：

當產品不使用時，應放在包裝盒內。倉庫溫度應在-40~70℃，相對濕度為5~95%，并且倉庫內不能有有害氣體，易燃品，爆炸品，腐蝕性等化學物品及強有力的機械震動、沖擊和磁場影響。包裝盒需放在距離地面至少20cm高，距離墻，熱源，和通風口50cm遠。充電器在此種存儲條件下可以放兩年，超過兩年須重新檢測。充電器必須每三個月通電一次，通電時間應不少于0.5小時。

Products should be stored in package box when it is not used. And warehouse temperature should be -40~value="70" tcsc="0" unitname="℃" w:st="on">70℃, and relative humidity is 5~95%. In the warehouse, there should not be harmful gas, inflammable, explosive products, and corrosive chemical products, and strong mechanical vibration, shock and strong magnetic field affection. The package box should be above ground at least 20cm height, and 50cm away from wall, thermal source, and vent. Under this requirement, product has 2 years of storage period, and should be rechecked when over 2 years.

9.可靠度需求Reliability requirements

MTBF（標準，環境溫度，負載要求）≥50K小時；

MTBF (standard, environmental temperature, load requirement) ≥50K hours;

測試條件:25℃,滿載，測試通過值。

testing condition: value="25" tcsc="0" unitname="℃" w:st="on">25℃,full load, testing proved value.

10. 充電曲線

    Charging Curve

nnecttype="rect" o:extrusionok="f">